|
Picture
|
Description
|
| |
|
Petroleum Industry. This 2 3/4" X 2" part is made of .052
Thick Galvanized Material. The Operations are blank, three
forms, pierce after formed, and cleaning. Approximate
tooling charge of $1,500.00 with 5,000 pieces costing
approximately $.75 each.
|
| |
|
Recreational Industry
This 24" x 1" part is made of .048 thick CRCQ (Cold Rolled Commercial Quality) material.
The operations are blank, pierce, deburr, four forms, and spot welded 10 times.
Approximate tooling charge of $5,900.00 with 2,500 pieces costing approximately $4.90 each.
|
| |
|
This 13” X 1” is made of .074 thick CRCQ (Cold Rolled Commercial Quality) Coil. The operations are blank, form, and pierced after formed, and deburr. Approximate tooling charge of $2,800.00 with 60,000 pieces costing approximately .55 cents each.
|
| |
|
Agricultural Industry. This 7.700" X 1.400" part is made of .250 thick HRPO(Hot Rolled Pickled Oiled)material. The manufacturing operations are blank, pierce, 3 forms, deburr, a powder coat paint, and assembled pin, spring, washer, pin, and split. Approximate engineering charge of $ 1,500.00 with 1,000 pieces costing approximately $3.00 each.
|
| |
|
This 3" x 1.25" part is made of .120
thick CRCQ(Cold Rolled Commercial Quality)material. The
manufacturing operations are blank,pierce, and deburr.
Welded to a 6.69" x .310 O.D rod with spring, and plated.
|
| |
|
This 4.3" x 2.25" part is made of 0.120 thick HRPO (Hot Rolled Pickled Oiled) material. The manufacturing operations are blank, pierce, three forms and a deburr.
|
| |
|
This 10" x 2.85" part is made of .090 thick Hot Rolled Pickled Oiled (HRPO) material and two weld nuts. The manufacturing operations are blank, pierce, deburr, three forms and a spot weld.
|
| |
|
This 6" x 1.1" part is made of .074 thick Electro-Galvanealed material. The manufacturing operations are blank, pierce, form and a cleaning.
|
| |
|
This part is made of 0.024 and 0.048 thick CRCQ (Cold Rolled Commerical Quality) material with three individual parts sizing 5” x 2.75”, 3.75” x 3.75” and 2” x 1.36”. Manufacturing operations are blank and pierce, two blanks, five forms, deburring and two spot welds
|
| |
|
Basic formed and flat stampings with different thicknesses and different hole sizes.
|
| |
|
This 3" x 6" part is made of .120 thick HRPO (Hot Rolled Pickled Oiled) material. The manufacturing operations are blank, form, pierce, and deburr.
|
| |
|
Diameters of these .060 thick CRCQ (Cold Rolled Commercial Quality) parts are 2.8" and 6.12". Manufacturing operations are two blank and pierce, three forms, a deburring and a spot weld.
|
| |
|
This 6.7 inch outside diameter part is made of .060 thick CRCQ (Cold Rolled Commercial Quality). The manufacturing operations are a blank/pierce, a form, a deburr and a spot-weld of 2 nuts.
|
| |
|
This 3.75" outside diameter x 2" inside diameter part is made of .120 thick CRCQ (Cold Rolled Commercial Quality) material. The manufacturing operations are blank, pierce, deburr, form and zinc plating.
|
| |
|
This 4" x 2 3/4" part is made of .120 thick HRPO (Hot Rolled Pickled Oiled) and .060 thick CRCQ (Cold Rolled Commercial Quality). The manufacturing operations are laser blanked, four forms, a deburring, a drill, a countersink, and two taps to insert the pop rivets.
|
| |
|
This 4" x 5" part is made of .187 thick HRPO (Hot Rolled Pickled Oiled) material. The manufacturing operations are three blanks, three pierce, three forms, a deburring, a flatten and a weld.
|
| |
|
This 12" x 13" part is made of .120 thick HSLA (High Strength Low Alloy) Grade 50 material. The manufacturing operations are blank and pierce, a pierce, a chamfer, a deburring, four forms and two tapped holes.
|
| |
|
This 4 1/2" x 5 1/2" part is made of .250 HSLA Grade 50 material. The manufacturing operations are three blanks, two pierce, one form, one pierce after form, a deburring and two welds.
|
| |
|
This 10" x 8" part is made of .250 and .312 HRPO (Hot Rolled Pickled Oiled) material. The manufacturing operations are five laser blanks, deburring, three forms and a weld.
|
| |
|
This 3" x 2 3/4" part is made of .064 thick galvanized material. The manufacturing operations are blank and pierce, two forms, and an assembly of two rivets and one purchased latch.
|
| |
|
This 2" x 4" part is made of .120 and .187 thick HRPO (Hot Rolled Pickled Oiled) material. The manufacturing operations are three blanks, a pierce, a form, a saw, a deburr and a weld.
|
| |
|
This 6" x 7" part is made of .120 thick HRPO (Hot Rolled Pickled Oiled) material. The operations to manufacture this part are two blanks, one pierce, four forms, a spot weld of four nuts, and a weld. The finish is black zinc.
|
| |
|
This 5" x 2 1/4" part and 1 1/4" x 1" component part are made of .080 thick CRS (Cold Rolled Steel). Manufacturing operations are two blanks, deburring, four forms, a heat treat, with three pieces of hardware inserted. The finish is process 4023 black.
|
| |
|
This 4" x 6" part is made of .179 and .187 HRPO (Hot Rolled Pickled Oiled) and .312 thick HR (Hot Rolled) plate. Manufacturing operations are three blank and pierce, a deburring, two forms, a spot weld and two welds.
|
| |